Tire chains are an excellent way to add traction when driving on snowy and icy roads. However, they should be put on the correct tires for them to work correctly.
Pull over in a safe spot and engage your parking brake. Remove the chains from their bag and plastic instructions mat.
How to Install Snow Chains
The chains may be a simple design, but installing them can be messy and time-consuming. Find a spot that’s free of snow and clear of any obstructions (like your fenders or shock absorbers) where you can pull over and get to work. Once you’ve pulled over, carefully remove the chains from their storage bag or box and roll them out beside each tire. Ensure that they lay straight, have no twists, and extend evenly over the tires. Also, ensure that any pointy hooks on the end of the chain point up and away from the rubber.
Once the chains are on, slowly drive forward a few car lengths to help them settle and recheck for tightness. You want to be able to wiggle them around on the tread by hand, but you shouldn’t be able to do so at high speeds. If you’re still not satisfied, pull over and repeat the process.
Depending on your local law, you may only need to put chains on one axle of your vehicle, but it’s safer to use them on all four wheels in case one wheel becomes unstable on the snow or ice. Plus, the chains will offer better traction for your car as it drives through heavier traffic or when passing slower vehicles.
It’s important to check your owner’s manual before attempting to install the chains yourself, but most models should have a system that lets you quickly and easily slip them on your car from start to finish. It’s a much more convenient way to go than the old method of laying out the chains and driving over them.
Remember, the chains will wear down faster if they’re left on too long or aren’t installed properly. They’ll also be more difficult to take off once the weather warms up, so only keep them on when they’re needed. It’s also a good idea to clean the chains with boiling water after each use to help prevent the build-up of dirt and other debris on them. And don’t forget to store them in a dry place so that they don’t rust.
Chains for All 4 Tires
While they can be expensive and a hassle to put on, snow chains for tires are necessary in some regions and provide excellent extra traction for your vehicle. They also protect your tires and help you avoid road damage from unnecessarily driving over dry pavement. However, the proper placement of tire chains is crucial for them to be effective. If you place the chain on the wrong wheel, it can cause it to slip and cause your car to lose control.
Fortunately, you can follow a few simple steps to ensure your chains fit correctly. First, start by placing your chains on the ground and pushing them firmly behind the wheel. Make sure that the yellow end goes directly behind the tire and the blue end is positioned on top. Next, pull up the slack to ensure that the chain is centred and not twisted.
After you’ve gotten the chains positioned, connect the blue and yellow ends using whatever fastening mechanism they use. If you have a set with rings fastened along the inside of the chains, these should rest on the bottom of your tire, close to the ground, during this process. Once you’ve connected on one side, come around to the other and do the same thing. After a couple of connections, you should have slack in the chain wrapped evenly over your tire, with equal coverage on both the inner and outer sidewalls.
Another way to install a set of tire chains is by using rubber grips. These are typically easier to install because they don’t require you to get under your vehicle or jack up the tire. However, they can be more expensive, and you’ll need to buy them individually for each tire.
If you’re looking for an economical and easy-to-install option, look for a set of tire chains with hooks. These are typically cheaper than rubber grips but still offer good traction. If you’re travelling long distances in snow, however, it’s best to go with a full set of chain traction devices that are designed for your specific tire size.
Chains for Rear-Wheel Drive Vehicles
If you are driving in areas where snow and ice are common, it’s best to have a set of chains on all four tires of your car. Although they may make it clunkier to drive and limit your speed, they are an inexpensive and effective way of getting traction on these slippery roads. However, it’s important to know how to put the chains on so you can do it correctly the first time you try it. Otherwise, you may end up damaging your chains or even your car.
First, find a safe location off the road to park your car while installing the chains. You will also want to make sure that your parking brake is set so you don’t accidentally drive off while installing them.
Start by draping the chain over your tire, taking care to center it correctly, and leaving an equal amount of slack on either side. You can also use this opportunity to fine-tune the position of your chains, making sure any pointy hooks are pointing away from the tread of the tire and not touching it.
Next, you will need to connect the red chain along the bottom. It is usually located on the right-hand side of your vehicle, directly opposite the connection to the gold chain above it. Once you have connected the chain, drive forward a few feet to expose the other portion that hasn’t been fitted, and repeat the process.
Once you’ve completed the installation process, you should be able to drive your car off of the chains and onto the road. Be sure to drive slowly, as if you go over too fast, you can cause damage to your chains or even the road surface. You should also avoid hitting curbs or potholes when you’re using chains, as this can break them and even cause them to come off.
Some states require you to carry or use a set of snow chains in certain weather conditions, so check your state’s laws to be sure. However, many drivers choose to have them on hand because of the increased traction they provide and to help ensure their safety in bad winter weather.
Chains for Front-Wheel Drive Vehicles
Many people have imagined or actually been in a situation where their car slips on the ice and snow, throwing off their balance and possibly even causing them to lose control. Chains help keep you on the road in these circumstances. They aren’t just a convenience; they can save lives if properly installed and used.
If you’re going to use chains, it’s important to put them on the correct tires. This will ensure they work properly and aren’t damaged. It’s also necessary to ensure you have enough clearance for the chains on your vehicle and to prevent them from rubbing against any components or destroying your tire treads.
Start by finding a safe spot to park your car, set the parking brake, and pull out your chains. Then, untangle the chains and find the yellow cable end on one side of the tire and the blue cable end on the other side. If you’re using traditional chains, it’s often easiest to connect the ends by slipping the yellow section into the blue and pulling the two sides together.
Place the chains on your front drive wheel, tucking them in behind the tire tread, with a small amount of slack hanging out in front of the car. You can then hop back in the driver’s seat and release the e-brake to drive about two feet forward, expose the open end of the chain on the inside rear wheel, and connect it. Repeat the process on the other tire, check for any loose ends, tuck them in, and hook them up.
Some types of chains will have rings fastened along their length. These go over the inside of the tire, resting on the bottom of the tire tread. It’s important to place the chains on in this way because the slack will keep them on the outside of the tire, where they aren’t as likely to cause damage and can prevent the chains from falling off as easily.
Once the chains are fitted, you’ll be ready to go. Remember to drive slowly, ideally, no more than 25 mph on snow or ice, so that the chains don’t rub against your car or cause it to become detached from the roadway. Don’t forget to check that you have sufficient clearance and clean the chains regularly to ensure they continue doing their job.